Looking for:
Fluke intellitone pro 200 manual |
Fluke intellitone pro 200 manual.Find It | Fluke Networks
Fluke Intellitone 200 Manual - Fluke intellitone pro 200 manual
Table Of Contents. Quick Links. Table of Contents. All rights reserved. All product names are trademarks of their respective companies. Previous Page. Next Page. Page 2 90 days, unless otherwise stated. Page 4 Testing for Continuity The IT toner detects telephone and Ethernet service, indicates polarity and active line numbers on voice circuits, and indicates active pair number on Ethernet circuits.
Page 7: Registration To www. Inspect the cases and test leads Table 1 describes the international electrical symbols used for damage before use. The probe turns off automatically after 1 hour of inactivity. Page 11 RJ11 and RJ45 connectors. Use the following: continuity test page 15 to check for shorts on Connect the IT toner to a jack or punch-down coax and non-terminated cables.
Locating and Isolating Cables The in the sequence. See text. Validating Cable Maps Note This test requires power from the Central Office. Turn the IT probes rotary switch to M locate. Use the probe to find the general location of the tone at a cable rack, patch panel, or behind a wall. In locating mode, the probes LEDs light up from 1 to 8 as the signal strength increases.
The higher the number, the stronger the signal. Note If you cannot locate the IntelliTone signal on 2-conductor cables, the cable may be shorted. Use the cable map test page 10 to test for shorts on cables with RJ11 and RJ45 connectors. Use the continuity test page 15 to check for shorts on coax and non-terminated cables.
Turn the probes rotary switch to N isolate. Use the probe to isolate the tone source in the cable bundle or at the patch panel. In isolating mode, the probes LEDs light up from 1 to 8 as the signal strength increases. SmartTone is intended for use on dry pairs of wires that are un-terminated at both ends of the run.
It is not intended to be used on live wires with a DC power source e. SmartTone works on many types of wire pairs including twisted pair, house wiring, and coax the shield is one wire and the center conductor is the other wire of the pair. SmartTone Positive Identification1.
The toner red lead must be connected to one of the wires of the pair, and the black lead must be connected to the other wire of the pair. Put the toner and probe in the H position.
At the far end of the cable run, place the probe near the wires you are tracing. Pick the pair that gives the loudest signal in the toner speaker. Short and release the two wires of the pair. If you hear a change in the pattern of the tone, then you have located the target pair of wires. If you dont hear a change in the tone pattern, then pick a different pair and try again until you find the pair that causes the tone pattern to change.
The cable map function finds the most common wiring faults on twisted pair cabling: shorts, opens, and crossed pairs. Turn the toners rotary switch to M If necessary, use the IP probe to locate the correct connector at the other end of the cabling, as described in the previous section. See Validating the Cables Shield on page Each LED that corresponding to an active pin flashes briefly, then should light for about 1 second.
The brief flash shows which LED is next in the sequence. The probe also beeps in different tones to indicate good wiring, miswires, shorts, and opens. Short: If two LEDs turn on for 1 second at the same time, those two pins are shorted together. If more than 2 wires are shorted together, the LEDs for the shorted pins indicate opens. Remove the battery door and disconnect the battery from the probe, as described under Battery Life and Replacement on page Note: The battery must be disconnected from the probe for at least 30 seconds.
Replace the battery and battery door. Remove the battery door and disconnect the battery from the probe. Note This test requires power from the Central Office. Turn off the toner. Connect the toner to the circuit as shown in Figure 3. Disconnect unused test leads and connectors from the toner.
The LEDs indicate telephone service and polarity as shown in Figure 3. Connect the toner to the circuit as shown in Figure 4. The toner checks for continuity between pins 4, 5.
Continuity indicates the toner is connected to a network device that is turned off. Testing for ContinuityYou can use the toner to test circuits and components for continuity. If you are testing a circuit, verify that it is not powered. Use the toners continuity E function to check for continuity. Use a voltage meter to check other types of circuits for power. Connect the toner to the circuit or component as shown in Figure 5. Turn the toners rotary switch to E. LED indicates an open or closed circuit as The shown in Figure 5.
IT Users Manual Maintenance Clean the case with a soft cloth dampened with water or a mild soap solution. WXWarningTo avoid possible electric shock or personal injury: Turn off the toner or probe and disconnect all test leads before replacing the battery. Battery Life and ReplacementThe toner and probe batteries last for about 20 hours of typical use. Figure 6 shows how to replace the battery in the toner and probe. Note The position of the probes rotary switch when the battery is replaced enables or disables shield validation for cable map tests.
WCautionTo avoid unreliable test results, replace the battery as soon as the low battery indication appears. See Battery Status on page 6. AccessoriesTo order accessories Table 2 , contact Fluke Networks. For the latest list of IT accessories and other cable testers visit the Fluke Networks website at www. Table 2. Accessory Test lead set, banana jacks to alligator clips Test lead set, banana jacks to alligator clips with bed of nails Soft carrying case.
Match case Limit results 1 per page. Author rkonc View Download 5. The SmartTone analog technology will change cadence when a pair is shorted at the far end. International Electrical Symbols Never use the toner, probe, or test leads if they are damaged. W Warning: Risk of personal injury.
See text. RJ45 Ethernet jack Green: service on 3, 6 Red: service on 1, 2 The toner checks for continuity between pins 4, 5. Validating Ethernet Service 14 Testing for Continuity Testing for ContinuityYou can use the toner to test circuits and components for continuity. WCautionTo avoid damaging the case, do not use solvents or abrasive cleansers.
Accessories Fluke Networks Model or Part Number MT MT MT Accessory Test lead set, banana jacks to alligator clips Test lead set, banana jacks to alligator clips with bed of nails Soft carrying case See text regarding probe's switch position during battery replacement. Weight with battery Toner: 6. LinkRunner Network Multimeter - shopflukenetworks.
Fluke Networks Documents. You can choose from a Documents. Please allow 4 — 6 weeks for Documents. IntelliTone Toner and Probe - fluketestery.
Fluke 10 kV Insulation Tester Kit IntelliTone Pro Toner Documents. IntelliTone Probe, six remote Documents.
❿ ❿
No comments:
Post a Comment